Generate QR code
Open Access
Subscription Access
Thermocyclic strength of grey cast iron SCh20 at high temperature shifts
https://doi.org/10.22349/1994-6716-2020-102-2-50-61
Abstract
To predict the durability of casting molds made of SCh20 cast iron under thermal fatigue during its filling by liquid metal the thermocyclic strength of the casting molds metal (grade SCh20 gray cast iron, analog of A48-30B AISI cast iron) was investigated. The specimens were tested by cyclic heating in the furnace to maximum temperatures from 700°С to 1000°C with following cooling in air and water. The Coffin equation and the dependence of crack growth rate in specimens are obtained on the basis of metallographic measurements of crack length in specimens and strain ranges FEM calculations. The investigations results allow one to predict the durability of casting molds made of SCh20 cast iron under thermal fatigue during its filling by liquid metal.
About the Authors
S. M. Balakin
NRC “Kurchatov Institute” – CRISM “Prometey”
Russian Federation
49 Shpalernaya St, 191015, St Petersburg
Russian Federation
49 Shpalernaya St, 191015, St Petersburg
L. A. Belyaeva
NRC “Kurchatov Institute” – CRISM “Prometey”
Russian Federation
Russian Federation
Cand Sc. (Eng)
49 Shpalernaya St, 191015, St Petersburg
N. A. Khlyamkov
NRC “Kurchatov Institute” – CRISM “Prometey”
Russian Federation
Russian Federation
Cand Sc. (Eng)
49 Shpalernaya St, 191015, St Petersburg
V. A. Petrov
NRC “Kurchatov Institute” – CRISM “Prometey”
Russian Federation
Russian Federation
Cand Sc. (Eng)
49 Shpalernaya St, 191015, St Petersburg
References
1. Andreev, V.V., Lubyanoy, D.A., Samsonov, Yu.N., Kaminskaya, I.A., Lub y a n a y a , S . V . , Razrabotka tekhnologii vnepechnoy obrabotki domennogo chuguna dlya izgotovleniya smennogo metallurgicheskogo oborudovaniya s povyshennoy ekspluatatsionnoy stoikostyu [Development of the technology of out-of-furnace treatment of blast iron for the manufacture of replaceable metallurgical equipment with increased operational stability], Metallurg, 2014, No 6,pp. 86–88.
2. Panteleeva, A.V., Kovalevich, E.V., Kompyuternoe modelirovanie napryazhennogo sostoyaniya izlozhnits dlya slitkov vysokolegirovannoy stali [Computer simulation of the stress state of moulds for high alloy steel ingots], Liteinoe proizvodstvo, 2013, No 7, pp. 21–23.
3. Mukhin, G.G., Belyakov, A.I., Aleksandrov, N.N., et al., Mashinostroenie. Entsiklopediya. Stali. Chuguny [Mechanical engineering. Encyclopedia. Steel. Cast iron], 2000, V. 2.
4. Sherman, A.D., Zhukov, A.A., Chugun [Cast iron]: Reference book, Moscow: Metallurgiya, 1991.
5. OST 5.9299-79: Industry Standard. Thermal fatigue and shaping during heat changes. Test methods.
6. Birger, I.A., Shorr, B.F., Termoprochnost detaley mashin [Heat resistance of machine parts], Moscow: Mashinostroenie, 1975.
7. Makhutov, N. A., Deformatsionnye kriterii razrusheniya i raschet elementov konstruktsiy na prochnost [Deformation criteria of failure and strength analysis of structural elements], Moscow: Mashinostroenie, 1981.
8. MR 125-02-95 “Rules of drawing up structural models and definition of parameters of loads for structure elements with discovered defect”, TSNIITMASh, Moscow, 1995.
Review
For citations:
Balakin S.M., Belyaeva L.A., Khlyamkov N.A., Petrov V.A. Thermocyclic strength of grey cast iron SCh20 at high temperature shifts. Voprosy Materialovedeniya. 2020;(2(102)):50-61. (In Russ.) https://doi.org/10.22349/1994-6716-2020-102-2-50-61
Views:
313
Email this article 