Generate QR code
Open Access
Subscription Access
Application of cold gas dynamic spraying as an additive technology for producing materials based on nickel aluminide and titanium aluminide
https://doi.org/10.22349/1994-6716-2021-107-3-118-127
Abstract
Metal additive manufacturing is widely studied for its unique advantages over traditional manufacturing processes. It is used to form complex components of Ti, Fe or Ni alloys. However, for non-ferrous alloys – aluminum, magnesium, copper – additive technologies are not used due to rapid melting during laser, electron beam and/or arc treatment. Cold spraying is widely used as an effective technology for applying high quality coatings in the mass production of metal and alloy products and/or metal matrix composite coatings. In addition, cold spraying is a serious and effective tool for the additive manufacturing of metals, and research in this area is currently becoming intense. During heat treatment of materials obtained by cold spraying, new chemical compounds are formed – both intermetallic compounds and hardening ceramic inclusions that increase the microhardness. However, as a result of a change in the structure during chemical transformations, a change in the geometry of the product and the formation of pores can be observed.
About the Author
D. A. Gerashchenkov
NRC “Kurchatov Institute” – CRISM “Prometey”
Russian Federation
Russian Federation
Cand Sc. (Eng)
49 Shpalernaya St, 191015, St Petersburg
References
1. Gibson, D., Rosen, International Publishing, 2010. B.S., Additive Manufacturing Technologies. New York: Springer
2. Gu, D.D., et al., Laser additive manufacturing of metallic components: materials, processes and mechanisms, Int. Mater. Rev. Taylor & Francis, 2012, V. 57, No 3, pp. 133–164
3. Murr Lawrence, E., Frontiers of 3D Printing/Additive Manufacturing: from Human Organs to Aircraft Fabrication, J. Mater. Sci. Technol., 2016, V. 32, No 10, pp. 987–995.
4. Assadi, H., et pp. 382–407. al., Cold spraying – A materials perspective, Acta Mater., 2016, V. 116,
5. Papyrin, A., Cold spray technology, Adv. Mater. Process., 2001, V. 159, pp. 49–51.
6. Arabgol, Z., et al., Analysis of Thermal History and Residual Stress in Cold-Sprayed Coatings, J. Therm. Spray Technol., 2014, V. 23, No 1, pp. 84–90
7. Li, W., et al., Solid-state additive manufacturing and repairing by cold spraying: A review, J. Mater. Sci. Technol., 2018, V. 34, No 3, pp. 440–457.
8. Ziemian, C.W., Wright, W.J., Cipoletti, D.E., Influence of Impact Conditions on Feedstock Deposition Behavior of Cold-Sprayed Fe-Based Metallic Glass, J. Therm. Spray Technol., 2018, V. 27, No 5, pp. 843–856.
9. Karmakar, R., Maji, P., Ghosh, S.K., A Review on the Nickel Based Metal Matrix Composite Coating, Metals and Materials International. Korean Institute of Metals and Materials, 2020.
10. Champagne, V., Helfritch, D., The unique abilities of cold spray deposition, Int. Mater. Rev. Taylor & Francis, 2016. V. 61, No 7, pp. 437–455.
11. Suhonen, T., et al., Residual stress development in cold sprayed Al, Cu and Ti coatings, Acta Mater., 2013, V. 61, pp. 6329–6337.
12. Coddet, P., et al., Comparison of the Properties of Cold-Sprayed Cu-0.5Cr-0.05Zr Alloys after Various Heat Treatments Versus Forged and Vacuum Plasma-Sprayed Alloys, J. Therm. Spray Technol, 2014, V. 23, No 3, pp. 486–491.
13. Coddet, P., et al., Mechanical Properties of Cu-0.1Ag Alloys Deposited by Cold Spray with Various Powder Feed Rate and Heat Treatment, J. Therm. Spray Technol, 2015, V. 24, No 1, pp. 119–125.
14. Pogrebnjak, A.D., et al., The structure and properties of high-entropy alloys and nitride coatings based on them, Russ. Chem. Rev. Turpion-Moscow Limited, 2014, V. 83, No 11, pp. 1027–1061.
15. Bagherifard, S., Roscioli, G., Zuccoli, M.V., Hadi, M., D’Elia, Demir, A.G.,Previtali, B., Kondбs, J.,Guagliano, M., Cold spray deposition of freestanding inconel samples and comparative analysis with selective laser melting, J. Therm. Spray Technol, 2017, V. 26, pp. 1517–1526.
16. Gerashchenkov, D.A., Farmakovsky, B.V., Vasiliev, A.F., Mashek, A.Ch., Issledovanie temperatury potoka v protsesse kholodnogo gazodinamicheskogo napyleniya funktsionalnykh pokrytiy [Study of the flow temperature in the cold gas-dynamic spraying of the functional coatings], Voprosy Materialovedeniya, 2014, V. 2, No 77, pp. 87–96.
17. Zhao, H., Bing, C., Formation of TiB2 CERAM INT, 1999, V. 25, pp. 353–358. -TiC Composites by Reactive Sintering, Ceram. Int. –
18. Pan, C., Zhang, J., Zhu, B., Structure formation and densification of TiB2 -TiC-Ni composites produced by chemical reaction of Ti-B4 C system in high-gravity field, IOP Conf. Ser. Mater. Sci. Eng., 2018, V. 382, p. 22049.
Review
For citations:
Gerashchenkov D.A. Application of cold gas dynamic spraying as an additive technology for producing materials based on nickel aluminide and titanium aluminide. Voprosy Materialovedeniya. 2021;(3(107)):118-127. (In Russ.) https://doi.org/10.22349/1994-6716-2021-107-3-118-127
Views:
434
Email this article 