Generate QR code
Open Access
Subscription Access
Structure and properties of the t-joints made of titanium alloy VT6S during diffusion brazing
https://doi.org/10.22349/1994-6716-2023-114-2-71-79
Abstract
The paper studies structural transformations of the brazing seam and fillet of the T-joints formed during the diffusion brazing of the titanium alloy VT6S with filler alloy of the Ti–Cu–Ni–Zr system. The soaking time during brazing under the designed temperature is regarded as one of the most important processing terms. It is shown that the satisfactory level of the mechanical properties of the joints could be achieved at the proper technological parameters that provide removal of any alloying additions from the brazing seam as well as the minimum fillet size. The lamellar structure of the base titanium alloy could be recommended as the most desirable for the diffusion of brazed joints.
About the Authors
A. I. Igolkin
TsNTU Prometey
Russian Federation
Russian Federation
Cand. Sc. (Eng)
29A, office 2n, Bakunin Ave, 191144 St Petersburg
N. V. Lebedeva
NRC “Kurchatov Institute” – CRISM “Prometey”
Russian Federation
Russian Federation
Cand. Sc. (Eng)
49 Shpalernaya St, 191015 St Petersburg
I. A. Maksimenko
NPF “Nevintermash”
Russian Federation
Russian Federation
11E Dobrolyubov Ave, 197198 St Petersburg
References
1. Bratukhin, A.G., Ivanov, U.L., Marin, B.N., et al., Shtampovka, svarka, paika i termoobrabotka titana i ego splavov v aviastroenii [Stamping, welding, soldering and heat treatment of titanium and its alloys in the aircraft industry], Moscow: Mashinostroenie, 1997.
2. Radzievsky, V.N., Tkachenko, G.G., Radzievsky, V.N., Tkachenko, G.G., Vysokotemperaturnaya vakuumnaya paika v kompressorostroenii [The high temperature vacuum brazing in machinery], Kiev: Ecotechnologia, 2009.
3. Kalin, B.A., Kalinin, U.N., Sevrukov, O.N., Fedotov, V.T., Grigoriev, A.E., Pajka tonkolistovykh konstruktsii iz titanovykh splavov amorfnymi pripoyami marki STEMET [The brazing of the thin-sheet constructions made of titanium alloys using amorphous filler metals of STEMET trademark], Svarochnoe proizvodstvo, 1996, No 9, pp.23–24.
4. Shang, L., Wang, G., Yang, D., Li, Y., Microstructure and performance analysis of vacuum brazing welded titanium joints in honeycomb sandwich panel structure, Transaction of the Chine Welding Institution, 2017, No 38(3), pp. 125–128.
5. Maksimova, S.V., Khorunov, V.F., Voronov, V.V., Vliyanie velichiny zazora i iskhodnogo sostoyaniya pripoya na strukturoobrazovanie payanykh soedinenii titana i ego splavov [The influence of the amount of the gap and the initial condition of the brazing filler metals on the structural transformation of the brazed joints of titanium and its alloys], Avtomaticheskaya svarka, 2013, No 33, pp.30–35.
6. Pomortsev, E.N., Chigarin, V.I., Gabdrakhmanova, Z.R., Titanovye splavy v tsentrobezhnykh kompressorakh [Titanium alloys for centrifugal compressors], Kompressornaya technika i pnevmatika, 2015, No 8, pp.38–41.
7. Ganjeh, E., Sarkhosh, H., Bajgholi, M.E., Khorsand, H., Ghaffari, M.H., Increasing Ti-6Al-4V brazed joint strength equal to the base metal by Ti and Zr amorphous filer alloy, Materials characterization, 2012, No 71, pp. 31–40.
8. Huang, Ch.-D., Hwang, J.-R., Huang, J.Y., Optimization of vacuum brazing process parameters in Ti-6Al-4V alloy, Metals, 2022, No 12(6).
9. Shapiro, A.E., Brazing of conventional titanium alloys, ASM Handbook, 2017, V. 6, pp. 36–43.
10. Borisova, E.A., Skliarov, N.M., Pozharobezopasnye titanovye splavy [The fireproof titanium alloys], Titan, 1993, No 3, pp. 21–24.
11. Kornilov, I.I., Titan: Istochniki, sostavy, svoistva, metallokhimiya i primenenie [Titanium. The sources, compositions, properties, metal chemistry and application], Mosow: Nauka, 1975.
12. Glazunov, S.G., Moiseev, V.N., Konstruktsionnye titanovye splavy [The structural titanium alloys], Moscow: Metallurgia, 1974.
Review
For citations:
Igolkin A.I., Lebedeva N.V., Maksimenko I.A. Structure and properties of the t-joints made of titanium alloy VT6S during diffusion brazing. Voprosy Materialovedeniya. 2023;(2(114)):71-79. (In Russ.) https://doi.org/10.22349/1994-6716-2023-114-2-71-79
Views:
289
Email this article 