Generate QR code
Open Access
Subscription Access
Effect of hot rolling mode on crys-tallographic texture and mechanical properties of directly quenched bainitic steel
https://doi.org/10.22349/1994-6716-2023-116-4-20-31
Abstract
The paper considers the effect of hot rolling mode on the structure, mechanical properties and crystallographic texture, as determined by EBSD, for a directly quenched thick plate of high strength bainitic steel. According to the obtained results, stronger strain hardening of austenite before the phase transformation leads to appearance of granular bainite and hence diminishes the final steel strength.
Keywords
high strength bainitic steel,
deformation mode of hot rolling,
direct quenching,
crystallographic texture,
deformed austenite,
lath bainite,
granular bainite
Supporting agencies: Experimental studies were carried out on the equipment of the Center for Collective Use «Composition, structure and properties of structural and functional materials» of the National Research Center «Kurchatov Institute» – Central Research Institute of Structural Materials «Prometey» with financial support from the state represented by the Ministry of Science and Higher Education – agreement № 13. TsKP. 21.0014 (075-11-2021-068).
About the Authors
K. Yu. Kurteva
NRC «Kurchatov Institute» – CRISM «Prometey»
Russian Federation
Russian Federation
49 Shpalernaya St, 191015 St Petersburg
E. A. Yakovleva
NRC «Kurchatov Institute» – CRISM «Prometey»
Russian Federation
Russian Federation
Cand. Sc. (Eng)
49 Shpalernaya St, 191015 St Petersburg
M. L. Fedoseev
NRC «Kurchatov Institute» – CRISM «Prometey»
Russian Federation
Russian Federation
49 Shpalernaya St, 191015 St Petersburg
A. A. Zisman
NRC «Kurchatov Institute» – CRISM «Prometey»
Russian Federation
Russian Federation
Dr Sc. (Phys-Math)
49 Shpalernaya St, 191015 St Petersburg
E. I. Khlusova
NRC «Kurchatov Institute» – CRISM «Prometey»
Russian Federation
Russian Federation
Dr Sc. (Eng)
49 Shpalernaya St, 191015 St Petersburg
References
1. Jonas, J.J., Transformation textures associated with steel processing, Microstructure and Texture in Steels, 2009, New York: Springer, pp. 3–17.
2. Zisman, A.A., Zolotorevsky, N.Yu., Petrov, S.N., Khlusova, E.I., Yashina, E.A., Lokalny teksturny analiz neodnorodnostei struktury v nizkouglerodistoi vysokoprochnoi stali posle zakalki s prokatnogo nagreva [Local textural analysis of structure inhomogeneities in low-carbon high-strength steel after quenching with rolling heating], Voprosy Materialovedeniya, 2020, No 3 (103), pp. 9–15.
3. Bain, E.C., The Nature of Martensite, Trans. AIME, 1924, V. 70, pp. 25–35.
4. Bunge, H.-J., Texture Analysis in Materials Science, Butterworths, 1982.
5. Brown, E.L., Deardo, A.J., On the origin of equiaxed austenite grains that result from the hot rolling of steel, Metall. Mater. Trans., 1981, V. 12, pp. 39–47.
6. Zisman, A.A., Petrov, S.N., Ptashnik, A.V., Kolichestvennaya attestatsiya beinitno-martensitnykh struktur vysokoprochnykh legirovannykh stalei metodami skaniruyushchei elektronnoi mikroskopii [Quantitative certification of bainite-martensitic structures of high-strength alloy steels by scanning electron microscopy], Metallurg, 2014, No 11, pp. 91–95.
7. Taylor, G.I., The mechanism of plastic deformation of crystals: Part 1, Proceedings of the Royal Society, 1934, V. 145, pp. 362–387.
8. Cayron, C., Baur, A., Loge, R., Intricate morphologies of laths and blocks in low-carbon martensitic steels, Materials and Design, 2018, V. 154, pp. 81–95.
9. Miyamoto, G., Iwata, N., Takayama, N., Furuhara, T., Quantitative analysis of variant selection in ausformed lath martensite, Acta Materialia, 2012, V. 60, pp. 1139–1148.
10. Takayama, N., Miyamoto, G., Furuhara, T., Effects of transformation temperature on variant pairing of bainitic ferrite in low carbon steel, Acta Materialia, 2012, V. 60, pp. 2387–2396.
11. Yashina, E.A., Zisman, A.A., Petrov, S.N., Zolot orevsky, N.Yu., Vyiavlenie kristallograficheskikh osobennostej beinitno-martensitnykh struktur v zavisimosti ot uslovii zakalki metodami EBSD analiza [Identification of crystallographic features of bainitic-martensitic structures depending on quenching conditions using EBSD analysis methods], Materials of 18th International scientific and technic school of youngmaterial scientists of the Urals, 2017, pp. 655–659.
12. De-Castro, D., Eres-Castellanos, A., Vivas, J., Caballero, F.G., San-Martin, D., Capdevila, C., Morphological and crystallographic features of granular and lath-like bainite in a low carbon microalloyed steel, Mater. Char., 2022, V. 184, pp. 111703. DOI: 10.1016/j.matchar.2021.111703.
13. Zolotorevsky, N.Y., Panpurin, S.N., Zisman, A.A., Petrov, S.N., Effect of ausforming and cooling condition on the orientation relationship in martensite and bainite of low carbon steels, Mater. Char., 2015, V. 107, pp. 278–282. DOI: 10.1016/j.matchar.2015.07.023.
14. Greninger, A.B., Troyano, A.R., The mechanism of martensite formation, Metals Trans., 1949, V.185, pp. 590–598.
Review
For citations:
Kurteva K.Yu., Yakovleva E.A., Fedoseev M.L., Zisman A.A., Khlusova E.I. Effect of hot rolling mode on crys-tallographic texture and mechanical properties of directly quenched bainitic steel. Voprosy Materialovedeniya. 2023;(4(116)):20-31. (In Russ.) https://doi.org/10.22349/1994-6716-2023-116-4-20-31
Views:
199
Email this article 