Generate QR code
Open Access
Subscription Access
Effect of powdered laser surfacing modes on structure and properties of wear-resistant coating and new medium carbon steel with yield strength 1500 MPa
https://doi.org/10.22349/1994-6716-2018-96-4-107-116
Abstract
This paper studies coatings obtained by laser cladding of M2 powder material (Hoganas, Belgium) on a new B1500 medium-carbon steel. The analysis of defects (pores, cracks), microstructure, phase composition, microhardness of the deposited coatings depending on heat input of laser radiation was performed. The results of tests for wear resistance of coating samples, which allow selecting the optimal modes of laser deposition, are presented.
Supporting agencies: The work was supported by the Ministry of Education and Science of the Russian Federation under the Grant Agreement No. 14.579.21.0003 (the unique project identifier is RFMEFI57914X0003).
About the Authors
T. V. Knyazyuk
NRC “Kurchatov Institute” – CRISM “Prometey”
Russian Federation
Russian Federation
Cand Sc. (Eng)
49 Shpalernaya St, 191015 St Petersburg
G. D. Motovilina
NRC “Kurchatov Institute” – CRISM “Prometey”
Russian Federation
Russian Federation
Cand Sc. (Eng)
49 Shpalernaya St, 191015 St Petersburg
V. V. Bobyr
NRC “Kurchatov Institute” – CRISM “Prometey”
Russian Federation
49 Shpalernaya St, 191015 St Petersburg
Russian Federation
49 Shpalernaya St, 191015 St Petersburg
V. V. Ryabov
NRC “Kurchatov Institute” – CRISM “Prometey”
Russian Federation
Russian Federation
Cand Sc. (Eng)
49 Shpalernaya St, 191015 St Petersburg
References
1. Grigoriants, A.G., Shiganov, I.N., Misyurov, A.I., Tekhnologicheskie protsessy lazernoi obrabotki [Technological processes of laser treatment], Textbook for high schools, Moscow: Bauman MSTU Publishers, 2006, p. 664.
2. Biriukov, V.P., Uluchshenie svoistv poverkhnosti pri lazernom legirovanii i naplavke pokrytii [Improvement of surface properties for laser alloying and coating deposition], Tyazheloe Mashinostroenie, 2011, No 7, pp. 7–10.
3. Lisunov, E.A., Kolpakov, A.V., Ekspress legirovanie poverkhnostnogo sloya stalnykh detalei [Express alloying of the surface layer of steel parts],Mezhdunarodny Zhurnal Eksperimentalnogo Obrazovaniya, 2013, no. 3, pp. 78–79.
4. Wu, B.C.J., Redman, E.J., Hard facing with Cobalt and Nickel Alloys, Welding Journal, 1994, pp. 63–68.
5. Raikis, O., Diodnye lazery dlya lazernogo plakirovaniya: status quo – quo vadis [Diode lasers for laser cladding: status quo – quo vadis], Photonics, 2015, No 3, p. 51.
6. Biriukov, V.P., Tatarkin, D.Y., Khriptovich, E.V., Fishkov, A.A., Opredelenie vliyaniya rezhimov lazernoi naplavki i sostava poroshkovykh materialov na iznosostoikost pokrytii [Determination of the effect of laser surfacing regimes and composition of powder materials on the wear resistance of coatings], Problemy Mashinostroeniya i Nadezhnosti Mashin, 2017, No 1, pp. 63–66.
7. Biriukov, V.P., Povyshenie iznosostoikosti pri lazernoi obrabotke pochvoobrabatyvayushchikh orudii [Increase of wear resistance inlaser processing of tillage tools], Trydy GOSNITI, 2011, V. 107, pp. 105– 106.
8. Biryukov, V.P., Petrova, I.M., Gadolina, I.V., Optimizatsiya rezhimov lazernoi naplavki dlya povysheniya kharakteristik soprotivleniya ustalosti stalnykh obraztsov i detalei mashin [Optimization of laser surfacing modes for increasing the fatigue resistance characteristics of steel specimens and machine parts], Uprochnyayushchie Tekhnologii i Pokrytiya, 2015, No 1 (121), pp. 3–6.
9. Biriukov, V.P., Vliyanie mnogostadiinykh termicheskikh tsiklov na povyshenie iznosostoikosti poverkhnostei treniya pri lazernom uprochnenii i naplavke pokrytii [Influence of multi-stage thermal cycles on increasing wear resistance of friction surfaces inlaser hardening and coating of coatings], Trenie i Smazka v Mashinakh i Mekhanizmakh, 2007, no. 12, pp. 15–21.
10. Biriukov, V.P., Uluchshenie svoistv poverkhnosti pri lazernom legirovanii i naplavke pokrytii [Improvement of surface properties for laser alloying and coating deposition], Tyazheloe Mashinostroenie, 2011, No 7, pp. 7–10.
11. Biriukov, V.P., Petrovsky, V.N., Murzakov, M.A., Vliyanie nanokarbidov tugoplavkikh metallov na tribologicheskie svoistva pokrytii pri lazernoi naplavke [Influence of refractory metal nanocarbides on the tribological properties of coatings in laser surfacing], Problemy Mashinostroeniya i Nadezhnosti Mashin, 2015, No 6, pp. 70–74.
12. Gureev, D. M., Optimizatsiya teplostoikosti bystrorezhushchikh stalei pri sochetanii obemnoi i lazernoi termoobrabotok [Optimization ofheat resistance of fast-cutting steels in combination of volumetric and laser heat treatment], Vestnik Samarskogo Gosudarstvennogo Tekhnicheskogo Universiteta, Seriya FizikoMatematicheskie Nauki, 2014, No 2 (35), pp. 156–167.
13. Riabov, V.V., Khlusova, E.I., Golosienko, S.A., Motovilina, G.D., Novye stali dlya selskokhozyaistvennogo mashinostroeniya [New steels for agricultural engineering], Metallurg, 2015, No 6, pp. 59–65.
Review
For citations:
Knyazyuk T.V., Motovilina G.D., Bobyr V.V., Ryabov V.V. Effect of powdered laser surfacing modes on structure and properties of wear-resistant coating and new medium carbon steel with yield strength 1500 MPa. Voprosy Materialovedeniya. 2018;(4(96)):107-116. (In Russ.) https://doi.org/10.22349/1994-6716-2018-96-4-107-116
Views:
492
Email this article 