Generate QR code
Open Access
Subscription Access
Synthesis and electron beam facing of TiB – TiC – titanium matrix hybrid composite powders
https://doi.org/10.22349/1994-6716-2018-95-3-89-101
Abstract
TiB – TiC – titanium matrix composite powders have been synthesized by self-propagating high temperature synthesis (SHS) in titanium, boron and carbon reactive powder mixtures. A target volume content of the titanium matrix (binder) in the powders was 50%. The SHS powders were cladded on VT1-0 titanium sheet by electron beam facing. A thickness of the cladded coatings varied from 1 to 3 mm depending on the pass number. A phase composition and a structure of the SHS powders and of the cladded coatings were invetigated be X-ray diffraction, optical and scanning electron microscopy. According to structure investigation and hardness profiles in the “coating – titanium base plate” transition zone an adhesion of the coating to the base is high. The hardness and abrasive wear resistance tests of the cladded coatings were carried out depending on the powder used for cladding. The maximum hardness increase of the coatings strengthened by titanium monoboride and titanium carbide inclusions is 2.2 times and abrasive wear resistance – 4.3 times as compared with VТ1-0 base. According to authors’ earlier results enhance hardness and abrasive wear resistant effects of titanium matrix by titanium carbide particles and titanium monoboride is near to the wear resistance of coatings deposited with SHS TiB + Ti powder, but ~5 times less than the wear resistance of coatings surfaced with SHS powder TiC + Ti.
Keywords
self-propagating high-temperature synthesis,
metal-matrix composites,
titanium monoboride,
titanium carbide,
titanium,
surfacing,
microstructure,
hardness,
abrasive wear resistance
Supporting agencies: the Russian Foundation for Basic Research (Grants No 16-08-00493a and No 16-48-700381)
About the Authors
G. A. Pribytkov
Institute of Strength Physics and Materials Science of the Siberian Branch of the RAS (ISPMS SB RAS)
Russian Federation
Russian Federation
Dr Sc (Eng)
2/4, Pr. Akademichesky, Tomsk, 634055
V. V. Korzhova
Institute of Strength Physics and Materials Science of the Siberian Branch of the RAS (ISPMS SB RAS)
Russian Federation
Russian Federation
Cand Sc. (Eng)
2/4, Pr. Akademichesky, Tomsk, 634055
M. G. Krinitsyn
Institute of Strength Physics and Materials Science of the Siberian Branch of the RAS (ISPMS SB RAS)
Russian Federation
Russian Federation
2/4, Pr. Akademichesky, Tomsk, 634055
I. A. Firsina
Institute of Strength Physics and Materials Science of the Siberian Branch of the RAS (ISPMS SB RAS)
Russian Federation
Russian Federation
Cand Sc. (Eng)
2/4, Pr. Akademichesky, Tomsk, 634055
References
1. Zwikker, U., Titan und Titanlegirungen, Springer-Verlag, 1974.
2. Pribytkov, G.A., Krinitsyn, M.G., Firsina, I.A., Durakov, V.G., Tverdost i abrazivnaya iznosostoykost elektronno-luchevykh pokrytiy karbid titana – titanovaya svyazka, naplavlennykh SVS kompozitsionnymi poroshkami [Hardness and abrasive wear resistance of electron-beam coatings surfaced with titanium carbide – titanium matrix synthesized composite powders], Voprosy Materialovedeniya, 2017, No 4, pp. 52–61.
3. Pribytkov, G.A., Korzhova V.V., Krinitsyn, M.G., Firsina, I.A., Sintez i elektronno-luchevaya naplavka kompozitsionnykh poroshkov monoborid titana – titanovaya svyazka [Synthesis and electron-beam facing of titanium monoboride – titanium matrix composite powders], Voprosy Materialovedeniya, 2018, No 1, pp. 88–102.
4. Ma, F., Wang, T., Liu, P., Li, W., Liu, X., Chen, X., Pan, D., Lu, W. Mechanical properties and strengthening effects of in situ (TiB + TiC) / Ti-1100 composite at elevated temperatures, Materials Science & Engineering A, 2016, V. 654, pp. 352–358.
5. Li, S., Kondoh, K., Imai, H., Chen, B., Jia, L., Umeda, J., Fu, Y., Strengthening behavior of in situ-synthesized (TiC–TiB) / Ti composites by powder metallurgy and hot extrusion, Materials and Design, 2016, V. 95, pp. 127–132.
6. Jia, L., Wang, X., Chen, B., Imai, H., Li, S., Lu, Z., Kondoh, K. Microstructural evolution and competitive reaction behavior of Ti–B4Csystem under solid-state sintering, Journal of Alloys and Compounds, 2016, V. 687, pp. 1004–1011.
7. Rahoma, H.K.S., Wang, X.P., Kong, F.T., Chen, Y.Y., Han, J.C., Derradji, M., Effect of (α+ β) heat treatment on microstructure and mechanical properties of (TiB + TiC) / Ti–B20 matrix composite, Materials and Design, 2015, V. 87, pp. 488–494.
8. Rahoma, H.K.S., Chen, Y.Y., Wang, X.P., Xiao S.L., Influence of (TiC + TiB) on the microstructure and tensile properties of Ti–B20 matrix alloy, Journal of Alloys and Compounds, 2015, V. 627, pp. 415–422.
9. Srinivasa Vadayar, K., Devaki Rani, S., Bhanu Prasad, V.V., Effect of boron carbide particle size and volume fraction of TiB–TiC reinforcement on Fractography of PM processed Titanium matrix Composites, Procedia Materials Science, 2014, V. 6, pp. 1329–1335.
10. Kim, I.Y., Choi, B.J., Kim, Y.J., Lee, Y.Z., Friction and wear behavior of titanium matrix (TiB + TiC) composites, Wear, 2011, V. 271, pp. 1962–1965.
11. Choi, B.-J., Kim, I.-Y., Lee, Y.-Z., Kim, Y.-J., Microstructure and friction/wear behavior of (TiB + TiC) particulate-reinforced titanium matrix composites, Wear, 2014, V. 318, pp. 68–77.
12. Sun, S.,Wang, M., Wang, L., Qin, J., Lu, W., Zhang, D., The influences of trace TiB and TiC on microstructure refinement and mechanical properties of in situ synthesized Ti matrix composite, Composites: Part B,2012, V.43,pp.3334–3337.
13. Fu, B.G., Wang, H.W., Zou, C.M., Wei, Z.J., Microstructural characterization of in situ synthesized TiB in cast Ti–1100-0.10B alloy, Trans. Nonferrous Met. Soc. China, 2015, V. 25, pp. 2206–2213.
14. Zhang, C.J., Kong, F.T., Xiao, S.L., Zhao, E.T., Xu, L.J., Chen, Y.Y., Evolution of microstructure and tensile properties of in situ titanium matrix composites with volume fraction of (TiB + TiC) reinforcements, Materials Science and Engineering A, 2012, V. 548, pp. 152–160.
15. Wang M.-M., Lu W.-J., Qin J., Ma F., Lu J., Zhang D. Effect of volume fraction of reinforcement on room temperature tensile property ofin situ (TiB + TiC)/Ti matrix composites, Materials and Design, 2006, V. 27, pp. 494–498.
16. Rangaraj, L., Barman, K., Divakar, C., Jayaram, V., Reactive hot pressing of Ti–B–C and Ti–C at 1200°C, Ceramics International, 2013, V. 39, pp. 5955–5961.
17. Tabrizi, S. G., Sajjadi, S.A., Babakhan,i A., Lu, W., Influence of spark plasma sintering and subsequent hot rolling on microstructure and flexuralbehavior of in-situ TiB and TiC reinforced Ti6Al4V composite, Materials Science & Engineering A, 2015, V. 624, pp. 271–278.
18. Lu, J., Qin, J., Chen, Y., Zhang, Z., Lu, W., Zhang, D., Superplasticity of coarse-grained (TiB + TiC)/Ti–6Al–4V composite, Journal of Alloys and Compounds, 2010, V. 490, pp. 118–123.
19. Wang, M.-M., Lu, W.-J., Qin, J., Zhang, D., Bo, J., Feng, Z., The effect of reinforcements on superplasticity of in situ synthesized (TiB+TiC)/Ti matrix composite, Scripta Materialia, 2006, V. 54, pp. 1955–1959.
20. Eriksson, M., Salamon, D., Nygren, M., Shen, Z., Spark plasma sintering and deformation of Ti–TiB2composites, Materials Science and Engineering A, 2008, V. 475, pp. 101–104.
21. Xie, L., Jiang, C., Lu, W., Zhan, K., Feng, Q., Wu, X., Wang, F., The recrystallization behavior of surface deformation layer of (TiB + TiC)/Ti–6Al–4V composite during isothermal annealing, Materials Science and Engineering A, 2011, V. 530, pp. 239–243.
22. Xie L., Z h o u Q., J in X., Wang Z., Jiang C., Lu W., Wang J., Wang Q. J. Effect of reinforcements on rolling contact fatiguebehaviors of titanium matrix composite (TiB + TiC)/Ti–6Al–4V, International Journal of Fatigue, 2014, V. 66, pp. 127–137.
23. Li, S., Kondoh, K., Imai, H., Chen, B., Jia, L., Umeda, J., Microstructure and mechanical properties of P/M titanium matrix composites reinforced by in-situ synthesized TiC–TiB, Materials Science and Engineering: A, 2015, V. 628, pp. 75–83.
24. Xie, L., Jiang, C., Lu, W., Zhan, K., Chen, Y., Investigation on the residual stress and microstructure of (TiB + TiC)/Ti–6Al–4V composite after shot peening, Materials Science and Engineering A, 2011, V.528,pp.3423–3427.
25. Xie, L., Jiang, C., Lu, W., The influence of shot peening on the surface properties of (TiB + TiC)/Ti–6Al–4V, Applied Surface Science,2013, V.280, pp.981–988.
26. Xie, L., Jiang, C., Lu, W., Chen, Y., Huang, J., Effect of stress peening on surface layer characteristics of (TiB + TiC)/Ti–6Al–4V composite, Materials and Design,2012, V.33,pp.64–68.
27. Xie, L., Wang, L., Jiang, C., Lu, W., The variations of microstructures and hardness of titanium matrix composite (TiB + TiC)/Ti–6Al–4V after shot peening, Surface & Coatings Technology, 2014, V. 244, pp. 69–77.
28. Akopyan, A.G., Dolukhanyan, S.K., Borovinskaya, I.P., Vzaimodeistvie titana, bora i ugleroda [Interaction of titanium, boron and carbon], Fizika goreniya i vzryva, 1978, No 3, pp. 70–79.
29. Panin, V.E., Belyuk, S.I., Durakov, V.G., Pribytkov, G.A., Rempe, N.G., Elektronno-luchevaya naplavka v vakuume: oborudovanie, tekhnologiya, svoistva pokrytiy [Electron beam surfacing in vacuum: equipment, technology, coating properties], Svarochnoe proizvodstvo, 2000, No. 2, pp. 34–38.
30. Song, M.S., Huang, B., Zhang, M.X., Li, J.G., Study of formation behavior of TiC ceramic obtained by self-propagating high-temperature synthesis from Al–Ti–C elemental powders, Int. Journal of Refractory Metals & Hard Materials, 2009, V. 27, pp. 584–589
Review
For citations:
Pribytkov G.A., Korzhova V.V., Krinitsyn M.G., Firsina I.A. Synthesis and electron beam facing of TiB – TiC – titanium matrix hybrid composite powders. Voprosy Materialovedeniya. 2018;(3(95)):89-101. (In Russ.) https://doi.org/10.22349/1994-6716-2018-95-3-89-101
Views:
338
Email this article 